Recent Post

Tampilkan postingan dengan label Alarm. Tampilkan semua postingan
Tampilkan postingan dengan label Alarm. Tampilkan semua postingan

Horn/Siren Circuit Inline Connector 2011 Chevrolet Impala Police Circuit

Horn/Siren Circuit Inline Connector 2011 Chevrolet Impala Police CircuitHorn/Siren Circuit Inline Connector 2011 Chevrolet Impala Police Circuit Diagram

This accouterment permits chump affiliation of a about-face to baddest either horn or siren operation back the horn pad is pressed. A 0.35 mm² (22 gauge) wire is affiliated to an in-line adapter in the horn ambit of the apparatus console accouter beneath the apparatus panel. The end of this accouter addendum is in a 1.5m (5 ft) bend of wire coiled beneath the apparatus panel.
Read More → Horn/Siren Circuit Inline Connector 2011 Chevrolet Impala Police Circuit

RANGKAIAN SECURITY ALARM MOBIL

RANGKAIAN ALARM MOBIL
Car Alarm Arming Horn Beep Canceller

It’s a great convenience that most modern cars come with a built in alarm, however it is nothing but noise pollution that the horn sounds when the alarm is armed. Disconnecting the alarm system from the horn relay will eliminate this, but prevent the horn from sounding in the even of an actual alarm. This circuit serves to silence the arming beep yet maintain the alarm by introducing a small delay into the signal. It sits between the alarm and horn relay. The alarm must provide a constant horn signal for at least 3 seconds before the horn relay is activated. That way the quick “beep” will never activate the horn relay, while the constant alarm signal will.

Component List:

C1 1 0.01uF Ceramic Disc Capacitor
C2 1 100uF 35V Electrolytic Capacitor
R1 1 1K 1/4W Resistor
R2 1 10K 1/4W Resistor
R3 1 15K 1/4W Resistor
R4 1 470 Ohm 1/4W Resistor
D1, D3, D4 3 1N4004 Rectifier Diode
D2 1 Red LED
U1 1 555 Timer IC
K1 1 SPST 12V Automotive Relay
MISC 1 Board, Wire, Socket For U1, Case

from: aaroncake.net
Read More → RANGKAIAN SECURITY ALARM MOBIL

RANGKAIAN ALARM SEPEDA MOTOR

Skema Rangkaian ALARM SEPEDA MOTOR


Overview

The circuit was designed to create an early warning alarm system against any form of theft that is significant to the owners of motorcycles or bikes.
Terminology

* Mercury Switch – a switch constructed into a sealed glass tube or envelope containing two or more electrical contacts and a small amount or a bead of liquid metal mercury
* BC547 – NPN small signal transistors designed for general purpose switching and amplification due to its low voltage, low current and three different gain selections
* BC557 – PNP general purpose transistors used for amplification and switching due to its low current and low voltage

Circuit Explanation

This alarm system can utilized any number of normally open switches like the mercury (tilt) switch. It functions by allowing or interrupting the flow of electric current in a circuit. The physical position or alignment of the switch in relation to the earth’s gravity is where the functionality of the switch depends a lot. No current will flow to the electrical contacts as long as the mercury stays on the lowest point of the glass bulb. However, once the switch is tilted at a certain angle or direction, the liquid mercury will be touching the set of contacts and will produce an electrical connection between the contacts. When the switch is tilted back to the opposite direction the electrical current stops immediately.

The mercury switch is positioned in such a way that they will close when the bike is lifted off its side stand, pushed forward off its center stand, or the steering is moved. The siren will then sound for at least one witch that will close. The alarm will reset, approximately after two minutes, when the switches have been opened again. Changing the value of capacitor C1 changes the time delay for the alarm to turn OFF. When the alarm is silent, no current is virtually used.

The circuit should be properly protected from condensation or dampness as these may cause the circuit to not to function properly. The components should fit the size of the enclosure so the wirings can be well protected. Alternatively, a hidden switch can be used instead of a key switch. Also, a relay’s normally closed contacts can be used while the ignition energizes the relay coil and the alarm will set itself upon turning OFF the ignition
Application

In general, motorcycle alarm systems function in a different way as compared with those in automobiles. These alarms can be created in several forms such as a remote receiver where the alarm has the capability to be controlled via a remote control; as tilt sensors where a mercury balance sensor is utilized by being hooked up on the motorcycle which is a guaranteed way of interference detection; and as shock sensors where a loud distress signal is produced due to the signal that is transmitted to the alarm box when the motorcycle is tampered with, touched, or moved.

Choosing the appropriate alarm system should consider the following factors like the speaker alarm dimensions, main unit dimensions, working temperature, static current, alerting volume, working frequency, range of remote, and basic functions such as auto re-arming, mute alarm, sensitivity adjustment of remote, anti-hijacking, remote finding of motorcycle, remote arm and disarm, and remote cutoff engine.

The mercury switches are very useful in different types of applications, in spite of the hazardous threat of the chemical mercury, especially when permitted to vaporize. Although it can be handled safely, the mercury can cause death or nerve damage if skin contact or accidental ingestion occurs. This is why lots of manufacturers started replacing the mercury switches with other mechanical method of interrupting electrical current. On the other hand, they are still sought because of their accuracy like the water level sensing, open/close mailbox, room thermostats, motion-activated bomb detectors, car hood and trunk light activation, and home lighting circuits.

Source:www.zen22142.zen.co.uk/Circuits/Alarm/motorcycle.htm
Read More → RANGKAIAN ALARM SEPEDA MOTOR